Hyundai Genesis: Premium AVN System / Speakers Repair procedures

Inspection
Troubleshooting of the speakers
   
When handling the speakers:
-
Do not cause shock to the speakers by dropping or throwing them.
-
Be careful not to drop water and oil on the speakers.
-
Use caution to handle the speaker because diaphragm made of paper is easily torn by impact or external force.
-
Audio system tuning may cause damage to the speakers. The modified speakers are not covered by the manufacturer’s warranty.
1.
Basic inspection
Loosen the screws to rule out the interference from the body trims and surrounding parts and then remove the speaker.
After removing the speaker, check the sound quality of the speaker with the connector plugged in.
2.
Inspection for each cause
(1)
Abnormal vibration
A.
Make sure the mounting screws are properly tightened before replacing the speaker.
B.
Reinstall the speaker and check that the symptom is resolved.
C.
If the symptom does not disappear, replace the speaker with a new one.
(2)
Noise
A.
Check that the speaker connector is properly connected and reinstall the connector if necessary.
B.
If noises occur in the radio mode, turn to the CD player mode.
C.
If noises occur in both modes, replace the speaker with a new one.
   
If noises occur only in the radio mode, the poor radio reception is the cause so do not replace the speaker.
(3)
Poor working
A.
Check the plus(+) and negative(-) speaker terminals using an ohmmeter.
B.
If resistance is measured at the specified value shown below, the speaker operation is normal.
C.
If the measured resistance is different from the specified value, replace the speaker.

Removal
Front door speakers
1.
Disconnect the negative (-) battery terminal.
2.
Remove the front door trim.
3.
Remove the front speaker (A) after loosening the screws.
(Refer to Body - "Front Door Trim")

4.
Remove the twitter speakers (A) after loosening the screws.

Rear door speakers
1.
Disconnect the negative (-) battery terminal.
2.
Remove the rear door trim.
(Refer to Body - "Rear Door Trim")
3.
Remove the rear speakers (A),(B) after loosening the screws.

4.
Remove the twitter speakers (A) after loosening the screws.

Crash pad center speaker
   
Take care not to scratch the crash pad and related parts.
1.
Disconnect the negative (-) battery terminal.
2.
Using a scraper or remover, remove the crash pad center speaker cover.

3.
After loosening the connector and screws, remove the center speaker (A).

Sub Woofer Speaker
1.
Disconnect the negative (-) battery terminal.
2.
Remove the rear seat.
(Refer to Body - "Rear Seat")
3.
Remove the rear package tray (A).
(Refer to Body - "Rear Seat")

4.
Remove the sub woofer speaker (A) after removing bolts (4EA).
Surround Speaker
1.
Disconnect the negative (-) battery terminal.
2.
Remove the rear seat.
(Refer to Body - "Rear Seat")
3.
Remove the rear package tray (A).
(Refer to Body - "Rear Seat")

4.
Remove the surround speaker (A) after removing screws (2EA).

Midrange Speaker (Crash Pad)
1.
Disconnect the negative (-) battery terminal.
2.
Remove the left/right crash pad side speaker grille (A).

   
Take care not to scratch the crash pad and related parts.
3.
Remove the midrange speaker (A) after removing the connector and screws.

Installation
Front Door Speaker
1.
Install the front door speaker.
2.
Install the front door trim.
Midrange Speaker (Crash Pad)
1.
Install the midrange speaker
2.
Install the crash pad side speaker grille.
3.
Connect the negative (-) battery terminal.
Rear Door Speaker
1.
Install the rear door speaker.
2.
Install the rear door trim.
Crash Pad Center Speaker
1.
Install the center speaker.
2.
Install the center speaker grille.
Subwoofer Speaker
1.
Install the subwoofer speaker.
2.
Install the rear package tray and rear seat.
Surround Speaker
1.
Install the surround speaker.
2.
Install the rear package tray and rear seat.
   
Make sure the speaker connectors are plugged in properly.
AVN Antenna Repair procedures
Inspection Glass Antenna Test 1. Wrap aluminum foil (A) around the tip of the tester probe (B) and move the probe along the grid line to check whether the circuit opens. 2. Bring one end ...

AUX jack Schematic Diagrams
Circuit Diagram ...

Other information:

Hyundai Genesis (DH) 2013-2016 Service Manual: Air Cleaner Repair procedures


Removal and Installation [Air Cleaner Assembly] 1. Disconnect the battery "-" terminal from the trunk room. 2. Remove the engine cover. (Refer to Engine And Transaxle Assembly - "Engine Cover") 3. Remove the engine room cover. (Refer to Engine And Transaxle Assembly - "Engine Cover") ...

Hyundai Genesis (DH) 2013-2016 Service Manual: Smart Key Repair procedures


Smart Key Smart Key Code Saving 1. Connect the DLC cable of GDS to the data link connector (16 pins) in driver side crash pad lower panel, turn the power on GDS. 2. Select the vehicle model and then do "Smart key code saving". 3. After selecting "Smart key teaching" menu, push "Enter" k ...

© 2013-2024 www.hgenesisdh.com