Hyundai Genesis: Air Conditioning System / Repair procedures

Hyundai Genesis (DH) 2013-2016 Service Manual / Heating, Ventilation and Air Conditioning / Air Conditioning System / Repair procedures

Refrigerant System Service Basics

Refrigerant Recovery

Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a(R-134a) from the air conditioning system.

•	Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.

•	Be careful when connecting service equipment.

•	Do not breathe refrigerant or vapor.

If accidental system discharge occurs, ventilate the work area before resuming the service.

Additional health and safety information may be obtained from the refrigerant and lubricant manufacturers.

1.	Connect a R-134a refrigerant Recovery/Recycling/Charging system (A) to the high-pressure service port (C) and the low-pressure service port (B) as shown, following the equipment manufacturer's instructions.

2.	Measure the amount of refrigerant oil removed from the A/C system after the recovery process is completed. Be sure to install the same amount of new refrigerant oil back into the A/C system before charging.

System Evacuation

Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a(R-134a) from the air conditioning system.

•	Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.

•	Be careful when connecting service equipment.

•	Do not breathe refrigerant or vapor.

If accidental system discharge occurs, ventilate the work area before resuming the service.

Additional health and safety information may be obtained from the refrigerant and lubricant manufacturers.

When an A/C system has been open to the atmosphere, such as during installation or repair, it must be evacuated using a R-134a refrigerant Recovery/Recycling/Charging system. (If the system has been open for several days, the receiver/drier should be replaced, and the system should be evacuated for several hours.)

2.	Connect a R-134a refrigerant Recovery/Recycling/Charging system (A) to the high-pressure service port (B) and the low-pressure service port (C) as shown, following the equipment manufacturer's instructions.

3.	If the low-pressure does not reach more than 93.3 kPa (700 mmHg, 27.6 in.Hg) in 10 minutes, there is probably a leak in the system. Partially charge the system, and check for leaks (see Refrigerant Leak Test.)

4.	Remove the low pressure valve from the low-pressure service port.

System Charging

Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a (R-134a) from the air conditioning system.

•	Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.

•	Be careful when connecting service equipment.

•	Do not breathe refrigerant or vapor.

If accidental system discharge occurs, ventilate the work area before resuming the service.

Additional health and safety information may be obtained from the refrigerant and lubricant manufacturers.

1.	Connect a R-134a refrigerant Recovery/Recycling/Charging system (A) to the high-pressure service port (B) as shown, following the equipment manufacturer's instructions.

2.	Add to the system the same amount of new refrigerant oil as the one removed during recovery. Use only specified refrigerant oil. Charge the system with R-134a refrigerant [700±25g (24.7±0.88oz.)]. Do not overcharge the system to prevent the compressor from damage.

Refrigerant Leak Test

Always conduct a leak test with an electronic leak detector whenever leakage or refrigerant is suspected and when conducting service operations which are accompanied by disassembly or loosening or connection fittings.

In order to use the leak detector properly, read the manual supplied by the manufacturer.

If a gas leak is detected, proceed as follows:

1.	Check the torque on the connection fittings and, if too loose, tighten to the proper torque. Check for gas leakage with a leak detector (A).

2.	If leakage continues even after the fitting has been tightened, discharge the refrigerant from the system, disconnect the fittings, and check their seating faces for damage. Always replace, even if the damage is slight.

3.	Check the compressor oil and add oil if required.

4.	Charge the system and recheck for gas leaks. If no leaks are found, evacuate and charge the system again.

Description and Operation

Refrigeration Cycle ...

Components and Components Location

Component Location Index Engine Room [Lambda Engine] 1. Expansion Valve2. Suction & Liquid Tube Assembly3. Service Port (Low Pressure)4. Service Port (High Pressure)5. A/C Pressure Transd ...

Other information:

Hyundai Genesis (DH) 2013-2016 Owners Manual: For best battery service

The battery is in the trunk. When replacing the battery, disconnect the negative (-) cable (1) and remove the positive (+) battery fuse box (2). Keep the battery securely mounted. Keep the battery top clean and dry. Keep the terminals and connections clean, tight, and coated wi ...

Hyundai Genesis (DH) 2013-2016 Service Manual: PGS Unit (Back & Blinde Unit) Schematic Diagrams

Circuit Diagram Input / Output Terminal Voltage No.SignalDescriptionlevel1ACCACCOFF(Less than 1V), ON(More than 8V)4C-CAN-LHigh Speed CAN low-11V-OUTVideo Out-13IGNIGN SignalON(More than 9V) / OFF(Less than 1V)16C-CAN-HHigh Speed CAN high-18GND-RRear Camera GND-19REAR-POWERVCC-REARON(6~7V) / ...