Hyundai Genesis (DH): Front Suspension System / Front Lower Arm Repair procedures

Hyundai Genesis (DH) 2013-2016 Service Manual / Suspension System / Front Suspension System / Front Lower Arm Repair procedures

Replacement
[4WD]
Remove the lateral arm
1.
Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from the front hub.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

   
Be careful not to damage the hub bolts when removing the front wheel and tire.
3.
Loosen the steering gear box mounting bolts and then pull the steering gear box in direction of down.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

4.
Loosen the flange bolt & lock nut.
Tightening torque :
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)
[RH]

[LH]

5.
Unscrew the flange bolt and lock nut (A) to disconnect the lateral arm from the strut assembly (B).
Tightening torque:
137.3 ~ 156.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)

6.
Remove the split pin and nut. And then disconnect the lateral arm from the knuckle using SST (09568-2J100).
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

7.
Install in the reverse order of removal.
8.
Check the front alignment.
(Refer to Tires/Wheels - "Alignment")
Remove the compression arm
1.
Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported
2.
Remove the front wheel and tire (A) from the front hub.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

   
Be careful not to damage the hub bolts when removing the front wheel and tire.
3.
Loosen the nut and then remove the compression arm from knuckle.
Tightening torque
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

4.
Loosen the flange bolt & lock nut, remove the compression arm (A).
Tightening torque:
137.3 ~ 156.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)

5.
Install in the reverse order of removal.
6.
Check the alignment.
(Refer to Tires/Wheels - "Alignment")
[2WD]
Remove the lateral arm
1.
Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from the front hub.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

   
Be careful not to damage the hub bolts when removing the front wheel and tire.
3.
Loosen the steering gear box mounting bolts and then pull the steering gear box in direction of down.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

4.
Loosen the flange bolt & lock nut.
Tightening torque :
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)
[RH]

[LH]

5.
Unscrew the flange bolt and lock nut to disconnect the lateral arm from the strut assembly.
Tightening torque:
137.3 ~ 156.9N.m (14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)

   

    Removal 1. Remove the front wheel and tire (A) from the front hub . Tightening torque: 88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)    

    Removal 1. Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported. 2. Remove the front wheel and tire (A) from the front hub.

    Other information:

    Hyundai Genesis (DH) 2013-2016 Service Manual: General Safety Information and Caution

    Instructions When Handling Refrigerant 1. R-134a liquid refrigerant is highly volatile. A drop on the skin of your hand could result in localized frostbite. When handling the refrigerant, be sure to wear gloves. 2. It is standard practice to wear goggles or glasses to protect your eyes, and gloves to protect your hands.

    Hyundai Genesis (DH) 2013-2016 Service Manual: Power Mosfet Repair procedures

    Inspection 1. Turn the ignition switch ON. 2. Manually operate the control switch and control the voltage of the blower motor. 3. Select the control switch to raise the voltage until high speed. Specification Fan Speed (Manual)Motor Voltage (V)13.

    Categories

     
    Copyright В© 2026 www.hgenesisdh.com - 0.0285