Hyundai Genesis: Power Windows / Description and Operation

Safety Function of Power Window
When driver door power window auto-up switch is operated, safety function is activated.
1.
Safety function condition
When the force of 100N (using the 10N/mm spring) is detected while the window is rising, the window is pulled down.
2.
Length of window reversing (except holding the auto-up switch)
A.
When jamming is detected within the range between 4mm and 250mm from the top of the B pillar the window is pulled down to 300mm from the top of the B pillar.

B.
When jamming is detected within the range of over 250mm from the top of the B pillar the window is pulled down to the lowest position if the total length of jammed object plus 50mm is below the window’s lowest position.

3.
The length of window moving downward
A.
When jamming is detected while pulling the auto-up switch.
> Window moves downward by 25mm from jamming position
B.
Auto-up function is not available for 5 seconds after the above operation.
> When pulling the auto-up switch, the manual-up function is activated (no safety function).
C.
When holding the auto-up switch after 5 seconds from above condition.
> Window is reverse until 25mm from jamming position.

4.
The area with the safety function not applied
Safety function is not available within the 4mm range from the top of the window frame.
How to initialize the safety power window
1.
Initializing of Battery Connection
When the battery power is removed for over 5 minutes, safety power window switch needs the initializing.
(1)
Power window operation before initializing
A.
Manual-Up/Safety function is available
B.
Auto-Up/Down function is not available
(If the Auto-up/down switch is being pushed, the manual up/down function is operated.)
(2)
Initialization
Close the window in window open position, and holding the switch in window full close position over the 0.2 second.
(If start the closing the window in window full close position, initializing could be failed.)
(3)
If initialize the safety power window in jamming status, could occur below conditions.
A.
Safety function is not available
(4)
Window position memorizing
Hall sensor is used to identify the window position and motor operation direction. ECU detects the uppermost position of the window and sets the position as ‘0’
(5)
Deinitialization
ECU is deinitialized if the following conditions are met. After deinitialization process, Auto-up and safety function are not activated.
Deinitialization conditions
A.
Repeating window downward movement 15 times in a row.
B.
Power supply is suspended while the motor is in operation.
C.
Driver seat door opens, IGN Off with the window glass positioned in Hard Stop -> IGN On within 2 seconds -> within 5 seconds with IGN On, entering manual down switch signal 3 times -> Deinitialization completed (if power is not on in 2 seconds, or the operation to be performed in 5 seconds, the deinitialization process shall be repeated from the beginning.)
(6)
Prevention of overheated motor
Software overheating prevention function is used to prevent the motor from overheating (but, EEPROM data shall be saved in ECU). There are 2
2.
Initializing of fail safe mode
(1)
If the window moved by compulsion and motor have a problem, power window switch could be entering the fail safe mode for user’s safety.
(2)
Power window operation in fail mode
A.
Auto/Manual-Down function is available
B.
Auto/Manual-Up function is not available
(When auto/manual-up is operated, window is rising 20mm and is stopped the moving.)
Components and Components Location
Component Location 1. DDM (Driver door module)2. ADM (Assistant door module)3. Front window motor4. Rear window motor5. Rear window switch ...

Power Window Motor Components and Components Location
Components ...

Other information:

Hyundai Genesis (DH) 2013-2016 Service Manual: Rear Assist Arm Repair procedures


Removal 1. Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported. 2. Remove the front wheel and tire (A) from the rear hub. Tightening torque: 88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)     Be careful not to damage the ...

Hyundai Genesis (DH) 2013-2016 Service Manual: Cylinder Head Cover Repair procedures


Removal LH Cylinder Head Cover 1. Disconnect the battery "-" terminal from the trunk room. 2. Remove the surge tank. (Refer to Intake And Exhaust System - "Surge Tank") 3. Remove the intake manifold. (Refer to Intake And Exhaust System - "Intake Manifold") 4. Remove the high-press ...

© 2013-2021 www.hgenesisdh.com