Hyundai Genesis: Cooling System / Water pump Repair procedures

Removal and Installation
1.
Disconnect the battery "-" terminal from the trunk room.
2.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly - "Engine Room Under Cover")
3.
Drain the engine coolant.
(Refer to Cooling System - "Coolant")
4.
Remove the drive belt.
(Refer to Timing System - "Drive Belt")
5.
Remove the water pump pulley (A).

Tightening torque :
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

6.
Remove the water pump (A) and gaskets (B).

   
Clean the contact face before assembly.
Always use a new gasket.
Always use a new seal bolt (Bolt C)

Tightening torque
A(3EA) :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
B(1EA) :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
C(1EA) :
21.6 ~ 26.5 N.m (2.2 ~ 2.7 kgf.m, 15.9 ~ 19.5lb-ft)
D(1EA) :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
E(1EA) :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
F(1EA) :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
G(4EA) :
21.6 ~ 23.5 N.m (2.2 ~ 2.4 kgf.m, 15.9 ~ 17.4lb-ft)

7.
To install, reverse the removal procedure.
8.
Fill the radiator with coolant and check for leaks.
(Refer to Cooling System - "Coolant")
Inspection
1.
Check each part for cracks, damage or wear, and replace the coolant pump assembly if necessary.
2.
Check the bearing for damage, abnormal noise and sluggish rotation, and replace the coolant pump assembly if necessary.
3.
Check for coolant leakage. If coolant leaks from hole, the seal is defective. Replace the coolant pump assembly.
   
A small amount of "weeping" from the bleed hole is normal.
Water pump Components and Components Location
Components 1. Water pump pulley2. Water pump3. Water pump gasket ...

Water pump Troubleshooting
Troubleshooting SymptomsPossible CausesRemedyCoolant leakage • From the bleed hole of the water pump Visually check • Check leaks after about ten-minute warming up. • If cool ...

Other information:

Hyundai Genesis (DH) 2013-2016 Service Manual: Front Seat Assembly Repair procedures


Replacement     • When installing the belt, make sure not to damage the pretensioner. 1. Remove the front anchor seat belt (A).     ?How to detach the anchor seat belt 1) Expose the red-colored indicator pin (A) by pushing the slot hole with a O 1 ...

Hyundai Genesis (DH) 2013-2016 Service Manual: Rear Differential Carrier Repair procedures


Removal 1. Remove the rear wheel and tire (A) from the rear hub. Tightening torque: 88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)     Be careful not to damage the hub bolts when removing the rear wheel and tire (A). 2. With the brake engaged, remove the s ...

© 2013-2025 www.hgenesisdh.com