Hyundai Genesis: Windshield Wiper/Washer / Front Wiper Motor Repair procedures

Removal
1.
Disconnect the negative (-) battery terminal.
2.
Remove the windshield wiper arm (A) and blade after removing a nut.
3.
If necessary of removing the wiper blade, push both sides of wiper tabs (A) and then remove the wiper blade.

4.
Remove the cowl top cover.
(Refer to Body - "Cowl Top Cover")
5.
Disconnect the wiper motor connector (A) from the wiper motor & linkage assembly.

6.
Remove the windshield wiper motor and linkage assembly (A) after removing 3 bolts.

7.
Hold the wiper motor crank arm and remove the upper linkage (A) from the wiper motor crank arm.

   
Before removing the wiper motor and linkage assembly, make sure that the motor stops in the auto-stop position
Before removing the wiper motor and linkage assembly, check the location and installation angle of the wiper motor crank arm and linkage.

8.
Remove the lower linkage (A) from the wiper motor crank arm.

   
Before removing the wiper motor and linkage assembly, check the location and installation angle of the wiper motor crank arm and linkage.
9.
Remove the crank arm (B) after loosening a nut (A).

10.
Remove the bracket (A) and motor (B) after loosening the screws )3EA).

Installation
1.
Install the wiper motor and linkage assembly and then connect the wiper motor connector.

Tightening torque:
6.9~10.8 Nm (0.7~1.1 kgf.m, 5.0~7.9 lbf.ft)

2.
Install the cowl top cover.
3.
Install the windshield wiper arm and blade.

Tightening torque:
22.5~26.5 Nm (2.3~2.7 kgf.m, 16.6~19.5 lbf.ft)

   
-
The windshield wiper motor must be cycled to make sure that it is in the park position.
If necessary, adjust the wiper arm and blade.
4.
Install the wiper arm and blade to the specified position.
A: Auto stop position (Blade)

Inspection
1.
The wiring harness system on the body can check the failed parts more rapidly with tester for the vehicle (GDS).
The tester (GDS) provides the following information.
(1)
Self diagnosis : Checking failure and code number (DCT)
(2)
Current data : Checking the system input/output data state
(3)
Actuation test : Checking the system operation condition
(4)
Additional function : Controlling other features including system option setting and zero point adjustment
2.
Select the 'Car model' and the system to be checked in order to check the vehicle with the tester.
3.
Select the module to be checked after selecting BCM.
   
Select 'BCM' and 'Instrument Panel Module (IPM)' to check the Instrument Panel Module (IPM).
4.
Select the Current data menu to search the current state of the input/output data.
The input/output data for the sensors corresponding to the 'Instrument Panel Module (IPM)' can be checked.
Front Wiper Motor Components and Components Location
Component Location 1. Cap2. Nut3. Wiper arm & blade4. Rivet5. Cowl top cover6. Bolt7. Wiper motor & linkage assembly8. Wiper motor connector ...

Front Washer Motor Repair procedures
Inspection Front Washer Motor 1. With the washer motor connected to the reservoir tank, fill the reservoir tank with water.     Before filling the reservoir tank with water, ch ...

Other information:

Hyundai Genesis (DH) 2013-2016 Service Manual: Rear Seat Belt Buckle Repair procedures


Replacement 1. Remove the rear seat cushion assembly. (Refer to Rear Seat - "Rear Seat Assembly") 2. Loosen the mounting bolt, and then remove the rear seat belt buckle (A). [LH] Tightening torque : 39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft) [RH] Tightening torque : 3 ...

Hyundai Genesis (DH) 2013-2016 Service Manual: Front Seat Shield Outer Cover Components and Components Location


Component Location 1. Front seat front shield outer cover2. Rear seat shield outer cover ...

© 2013-2025 www.hgenesisdh.com