Hyundai Genesis: General Information / General Information

General
The supplemental restraint system (SRS) is designed to supplement the seat belt to help reduce the risk or severity of injury to the driver and passenger by activating and deploying the driver, passenger, side airbag and belt pretensioner in certain frontal or side collisions.
The SRS (Airbag) consists of ; a driver side airbag module located in the center of the steering wheel, which contains the folded cushion and an inflator unit ; a passenger side airbag module located in the passenger side crash pad contains a folded cushion assembled with an inflator unit ; side airbag modules located in the front seat contain a folded cushion and an inflator unit ; curtain airbag modules located inside the headliner contains folded cushions and inflator units. The impact sensing function of the SRSCM is carried out by an electronic accelerometer that continuously measures the vehicle’s acceleration and delivers a corresponding signal through amplifying and filtering circuitry to the microprocessor.
SRSCM (SRS Control Module)
SRSCM will detect front impact with a front impact sensor, and side impact with a side impact sensor to determine airbag module deployment.
1.
DC/DC converter: DC/DC converter in the power supply unit includes up/down transformer converter, and provide ignition voltage for 2 front airbag ignition circuits and the internal operation voltage of the SRSCM. If the internal operation voltage is below critical value setting, it will perform resetting.
2.
Back up power supply: SRSCM has a separate back up power supply, that will supply deployment energy instantly in low voltage condition or upon power failure by a frontal crash.
3.
Self diagnosis: SRSCM will constantly monitor current SRS operation status and detect system failure while vehicle power supply is on, system failure may be checked with trouble codes using GDS.
4.
Airbag warning lamp on: When an error is detected, the module will transmit a signal to the SRSCM indicator lamp located on the cluster. MIL lamp will notice the driver of SRS error. Upon ignition key on, SRS lamp will turn on for about six seconds.
5.
Trouble code registration: When an error occur in the system, SRSCM will store a DTC corresponding to the error. DTC can be cleared only by GDS. However, if an internal fault code is logged or if a crash is recorded the fault clearing should not happen.
6.
Self diagnostic connector: Data stored in SRSCM memory will be output to GDS or other external output devices through connector located below driver side crash pad.
7.
Once airbag is deployed, SRSCM should not be used again but replaced.
8.
SRSCM will determine whether passenger put on seat belt by the signal from built-in switch in seat belt buckle, and deploy front seat airbag at each set crash speed.
9.
Side airbag deployment will be determined by the SRSCM that detects satellite sensor impact signal upon a side crash, irrespective to the seat belt condition.
General Information
...

Specifications
Tightening Torques ItemN.mkgf.mlb-ftPassenger airbag (PAB)7.8 ~ 11.80.8 ~ 1.25.8 ~ 8.7Side airbag (SAB)6.9 ~ 8.80.7 ~ 0.95.1 ~ 6.5Curtain airbag (CAB)11.8 ~ 14.71.2 ~ 1.58.7 ~ 10.9Knee airbag (K ...

Other information:

Hyundai Genesis (DH) 2013-2016 Service Manual: Under Body Body Repair


Projected Dimensions [2WD] * These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] [4WD]Actual Measurement Dimensions * These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] Front [2WD] * Thes ...

Hyundai Genesis (DH) 2013-2016 Service Manual: Drive Belt Tensioner Repair procedures


Removal and Installation 1. Remove the drive belt. (Refer to Timing System - "Drive Belt") 2. Remove the drive belt auto tensioner (A). Tightening torque Bolt (B) : 81.4 ~ 85.3 N.m (8.3 ~ 8.7 kgf.m, 60.0 ~ 62.9 lb-ft) Bolt (C) : 17.7 ~ 21.6 N.m (1.8 ~ 2.2 kgf.m, 13.0 ~ 15.9 b-ft) ...

© 2013-2024 www.hgenesisdh.com