Hyundai Genesis: Lubrication System / Engine Oil Repair procedures

Replacement
   
Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful substance which may cause skin cancer.
Use caution to minimize the length and frequency of contact of your skin to used oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use water-less hand cleaner, to remove any used engine oil. Do not use gasoline, thinners, or solvents.
In order to preserve the environment, used oil and used oil filter must be disposed of only at designated disposal sites.
1.
Park the car on the level ground.
Start the engine and let it warm up.
2.
Wait for 5 minutes after loosening the oil filter cap to fully drain the oil from the oil filter.
3.
Remove the engine under cover.
4.
Drain engine oil.
(1)
Remove the oil filler cap.
(2)
After lifting the car, remove the oil drain plug (A) and drain oil into a container.
5.
Replace the oil filter.
(1)
Disconnect the oil filter cap (A) from the oil filter body.
Turn the cap slightly and wait a minute to allow the residual oil in the filter to run out.
Then, remove the cap completely.

(2)
Remove the oil filter element.
(3)
Check the part number of a new oil filter is the same as the old one.
(4)
Install a new oil filter element (A) and new O-ring (B).

   
Check whether the o-ring is installed in the proper place.
(5)
Apply clean engine oil to the new O-rings.
Lightly screw the oil filter cap into place, and tighten it until the O-ring contacts the seat.
(6)
Finally tighten it again with specified tightening torque.

Tightening torque :
31.4 ~ 38.2 N.m (3.2 ~ 3.9 kgf.m,23.1 ~ 28.2 Ib-ft)

6.
Fill new engine oil.
(1)
Install the oil drain plug (A) with a new gasket.

Tightening torque :
34.3 ~ 44.1N.m (3.5 ~ 4.5kgf.m, 25.3 ~ 32.5lb-ft)

(2)
Fill new engine oil, while checking the oil level on the dipstick.

Capacity
Total : 7.3 L (7.71 U.S qt., 6.42 lmp.qt., 1.92 U.S.gal.)
Oil pan : 6.8 L (7.18 U.S qt., 5.98 lmp.qt., 1.79 U.S.gal.)
Drain and refill including oil filter :
6.9 L (7.29 U.S.qt., 6.06 lmp.qt., 1.82 U.S.gal.)

(3)
Install the oil filler cap.
7.
Start the engine and check that no oil leaks from the drain plug or oil filter.
8.
Recheck the engine oil level.
Inspection
1.
Check the engine oil quality.
Check the oil deterioration, addition of water or coolant, discoloring or thinning.
If the quality is visibly poor, replace the oil.
2.
Check the engine oil level.
Warm up and stop the engine, and then wait 5 minutes before checking whether the oil level is between the “F” and “L” marks in the dipstick.
If the level is lower than “L,” check for leakage and add oil up to the “F” mark.
   
Do not fill with engine oil above the “F” mark.
Selection Of Engine Oil
Recommendation :
- ACEA A5 or above / 5W-30
Allowed Oil Grade :
- ACEA A3, A5 or above
Allowed SAE Viscosity

   
For best performance and maximum protection of all types of operation, select only those lubricants which:
1.
Satisfy the requirement of the ACEA classification.
2.
Have proper SAE grade number for expected ambient temperature range.
3.
Lubricants that do not have both an SAE grade number and ACEA service classification on the container should not be used.
Lubrication System
...

Engine Oil Flow Diagram
Engine oil flow diagram ...

Other information:

Hyundai Genesis (DH) 2013-2016 Owners Manual: Instrument panel fuse panel


Inside the fuse/relay box cover, you can find the fuse/relay label describing fuse/relay name and capacity. ✽ NOTICE Not all fuse panel descriptions in this manual may be applicable to your vehicle; the information is accurate at the time of printing. When you inspect the fuse box ...

Hyundai Genesis (DH) 2013-2016 Service Manual: TPMS Sensor Description and Operation


Description 1. General description WU is a sensor placed in the tire that reports pressure and temperature. The WU is mounted inside the wheels, fixed to the valve. The angle between the valve and the housing of the WU is variable. This allows adaptation to various types of rims. The Wheel ...

© 2013-2024 www.hgenesisdh.com